Zachodniopomorski Uniwersytet Technologiczny w Szczecinie

Wydział Technologii i Inżynierii Chemicznej - Materials Science and Engineering (S1)

Sylabus przedmiotu Advanced Manufacturing Processes:

Informacje podstawowe

Kierunek studiów Materials Science and Engineering
Forma studiów studia stacjonarne Poziom pierwszego stopnia
Tytuł zawodowy absolwenta inżynier
Obszary studiów charakterystyki PRK, kompetencje inżynierskie PRK
Profil ogólnoakademicki
Moduł
Przedmiot Advanced Manufacturing Processes
Specjalność przedmiot wspólny
Jednostka prowadząca Katedra Technologii Materiałowych
Nauczyciel odpowiedzialny Jolanta Baranowska <Jolanta.Baranowska@zut.edu.pl>
Inni nauczyciele
ECTS (planowane) 8,0 ECTS (formy) 8,0
Forma zaliczenia egzamin Język angielski
Blok obieralny 7 Grupa obieralna 1

Formy dydaktyczne

Forma dydaktycznaKODSemestrGodzinyECTSWagaZaliczenie
wykładyW5 30 2,00,25egzamin
laboratoriaL5 60 4,00,50zaliczenie
ćwiczenia audytoryjneA5 30 2,00,25zaliczenie

Wymagania wstępne

KODWymaganie wstępne
W-1approval in subjects: Physic of Materials, Intro to MatSci/Intro to MatEng, Structure of Solids, Materials processing, Surface Science and Interfacial Phenomena

Cele przedmiotu

KODCel modułu/przedmiotu
C-1to get knowledge about selected advanced manufacturing technologies
C-2formation of skills in the area of technological processes preparation and carrying out.

Treści programowe z podziałem na formy zajęć

KODTreść programowaGodziny
ćwiczenia audytoryjne
T-A-1Study on influence of synthesis parameters on the physicochemical properties of selected nanostructures produced via vapor deposition techniques: case studies (10h)10
T-A-2Kinetic theory of gases – solving problems10
T-A-3Proper design of adhesive joints. Case analysis and theoretical prediction of joint’s bearing capacities10
30
laboratoria
T-L-1Influence of process parameters on coating deposition by magnetron sputtering techniques5
T-L-2Advanced deposition of polymer thin films by MAPLE method5
T-L-3Influence of process parameters on thin film deposition by pulsed laser and pulsed electron beam method5
T-L-4Formation of FexN layers under variable nitriding potential during gaseous nitridation of iron10
T-L-5Magnetron sputtering for preparation of sandwich structure nanolayers5
T-L-6Attenuation effect of thin films in EDS/XPS spectroscopies5
T-L-7Modification of particle size obtained via magnetron sputtering via sintering5
T-L-8Experimental comparison of adhesive joints strength prepared wit different polymer adhesives (part I – preparation, part II -determination of strength)5
T-L-9Degradation of waste polymer into metal-organic framworks (MOFs)10
T-L-10SLA manufacturing technology. Design, printing and post-processing5
60
wykłady
T-W-1Principles of the kinetic theory of gasses4
T-W-2Magnetron sputtering in coatings and thin films deposition2
T-W-3Lithography and surface etching2
T-W-4Vapor deposition techniques for growing nanostructures: chemical vapor deposition (CVD) and physical vapor deposition (PVP) and their modification7
T-W-5Thin polymer films formation by LBL and sping coating techniques; thin biological layers formation3
T-W-6High energetic beams used for thin films deposition and their influence on coating structure and properties; process parameters selections; kinetics of coatings growth7
T-W-7Rapid protopyping of polymers using photocuring and thermoforming prosessing (FDM, SLA)3
T-W-8Electrospinning of polymer nanofibres2
30

Obciążenie pracą studenta - formy aktywności

KODForma aktywnościGodziny
ćwiczenia audytoryjne
A-A-1Participation in recitations30
A-A-2Preparing for recitations23
A-A-3Preparing for tests5
A-A-4Consultations2
60
laboratoria
A-L-1participation in laboratory exercises60
A-L-2preparing for laboratory exercises30
A-L-3Preparation of reports20
A-L-4Consultations10
120
wykłady
A-W-1participation in lectures30
A-W-2self-study of the literature17
A-W-3preparing for the exam10
A-W-4The exam1
A-W-5Consultations2
60

Metody nauczania / narzędzia dydaktyczne

KODMetoda nauczania / narzędzie dydaktyczne
M-1interactive lectures, use of presentation (e.g. Powerpoint), films
M-2Auditorium Exercises
M-3Laboratory exercises

Sposoby oceny

KODSposób oceny
S-1Ocena podsumowująca: written exam
S-2Ocena formująca: questions
S-3Ocena formująca: reports

Zamierzone efekty uczenia się - wiedza

Zamierzone efekty uczenia sięOdniesienie do efektów kształcenia dla kierunku studiówOdniesienie do efektów zdefiniowanych dla obszaru kształceniaOdniesienie do efektów uczenia się prowadzących do uzyskania tytułu zawodowego inżynieraCel przedmiotuTreści programoweMetody nauczaniaSposób oceny
MSE_1A_C18b_W01
Student describes issues concerning advanced manufacturing processes
MSE_1A_W07C-1T-W-1, T-W-2, T-W-3, T-W-4, T-W-5, T-W-6, T-W-7, T-W-8M-1S-1

Zamierzone efekty uczenia się - umiejętności

Zamierzone efekty uczenia sięOdniesienie do efektów kształcenia dla kierunku studiówOdniesienie do efektów zdefiniowanych dla obszaru kształceniaOdniesienie do efektów uczenia się prowadzących do uzyskania tytułu zawodowego inżynieraCel przedmiotuTreści programoweMetody nauczaniaSposób oceny
MSE_1A_C18b_U01
Student has skills in advanced manufacturing processes
MSE_1A_U08C-2T-A-1, T-L-1, T-A-2, T-A-3, T-L-2, T-L-3, T-L-4, T-L-5, T-L-6, T-L-7, T-L-8, T-L-9, T-L-10M-2S-2, S-3

Zamierzone efekty uczenia się - inne kompetencje społeczne i personalne

Zamierzone efekty uczenia sięOdniesienie do efektów kształcenia dla kierunku studiówOdniesienie do efektów zdefiniowanych dla obszaru kształceniaOdniesienie do efektów uczenia się prowadzących do uzyskania tytułu zawodowego inżynieraCel przedmiotuTreści programoweMetody nauczaniaSposób oceny
MSE_1A_C18b_K01
Competences in advanced manufacturing of engineering materials
MSE_1A_K02C-1T-W-1, T-A-1, T-L-1, T-W-2, T-W-3, T-W-4, T-W-5, T-W-6, T-A-2, T-A-3, T-L-2, T-L-3, T-L-4, T-L-5, T-L-6, T-L-7, T-L-8, T-L-9, T-L-10, T-W-7, T-W-8M-1, M-3S-1, S-3

Kryterium oceny - wiedza

Efekt uczenia sięOcenaKryterium oceny
MSE_1A_C18b_W01
Student describes issues concerning advanced manufacturing processes
2,0
3,0Student describes selected issues at a basic level (score => 50%)
3,5
4,0
4,5
5,0

Kryterium oceny - umiejętności

Efekt uczenia sięOcenaKryterium oceny
MSE_1A_C18b_U01
Student has skills in advanced manufacturing processes
2,0
3,0Student describes selected issues at a basic level (score => 50%)
3,5
4,0
4,5
5,0

Kryterium oceny - inne kompetencje społeczne i personalne

Efekt uczenia sięOcenaKryterium oceny
MSE_1A_C18b_K01
Competences in advanced manufacturing of engineering materials
2,0
3,0Student describes selected issues at a basic level (score => 50%)
3,5
4,0
4,5
5,0

Literatura podstawowa

  1. Mikell Groover, Introduction to Manufacturing Processes, Wiley, 2011
  2. Prof. Dr.‐Ing. Friedrich‐Wilhelm Bach Dr. Andreas Laarmann Dipl.‐Ing. Thomas Wenz, Modern Surface Technology, Springer, 2006
  3. Ian GibsonDavid W. RosenBrent Stucker, Additive Manufacturing Technologies, Springer, 2010

Treści programowe - ćwiczenia audytoryjne

KODTreść programowaGodziny
T-A-1Study on influence of synthesis parameters on the physicochemical properties of selected nanostructures produced via vapor deposition techniques: case studies (10h)10
T-A-2Kinetic theory of gases – solving problems10
T-A-3Proper design of adhesive joints. Case analysis and theoretical prediction of joint’s bearing capacities10
30

Treści programowe - laboratoria

KODTreść programowaGodziny
T-L-1Influence of process parameters on coating deposition by magnetron sputtering techniques5
T-L-2Advanced deposition of polymer thin films by MAPLE method5
T-L-3Influence of process parameters on thin film deposition by pulsed laser and pulsed electron beam method5
T-L-4Formation of FexN layers under variable nitriding potential during gaseous nitridation of iron10
T-L-5Magnetron sputtering for preparation of sandwich structure nanolayers5
T-L-6Attenuation effect of thin films in EDS/XPS spectroscopies5
T-L-7Modification of particle size obtained via magnetron sputtering via sintering5
T-L-8Experimental comparison of adhesive joints strength prepared wit different polymer adhesives (part I – preparation, part II -determination of strength)5
T-L-9Degradation of waste polymer into metal-organic framworks (MOFs)10
T-L-10SLA manufacturing technology. Design, printing and post-processing5
60

Treści programowe - wykłady

KODTreść programowaGodziny
T-W-1Principles of the kinetic theory of gasses4
T-W-2Magnetron sputtering in coatings and thin films deposition2
T-W-3Lithography and surface etching2
T-W-4Vapor deposition techniques for growing nanostructures: chemical vapor deposition (CVD) and physical vapor deposition (PVP) and their modification7
T-W-5Thin polymer films formation by LBL and sping coating techniques; thin biological layers formation3
T-W-6High energetic beams used for thin films deposition and their influence on coating structure and properties; process parameters selections; kinetics of coatings growth7
T-W-7Rapid protopyping of polymers using photocuring and thermoforming prosessing (FDM, SLA)3
T-W-8Electrospinning of polymer nanofibres2
30

Formy aktywności - ćwiczenia audytoryjne

KODForma aktywnościGodziny
A-A-1Participation in recitations30
A-A-2Preparing for recitations23
A-A-3Preparing for tests5
A-A-4Consultations2
60
(*) 1 punkt ECTS, odpowiada około 30 godzinom aktywności studenta

Formy aktywności - laboratoria

KODForma aktywnościGodziny
A-L-1participation in laboratory exercises60
A-L-2preparing for laboratory exercises30
A-L-3Preparation of reports20
A-L-4Consultations10
120
(*) 1 punkt ECTS, odpowiada około 30 godzinom aktywności studenta

Formy aktywności - wykłady

KODForma aktywnościGodziny
A-W-1participation in lectures30
A-W-2self-study of the literature17
A-W-3preparing for the exam10
A-W-4The exam1
A-W-5Consultations2
60
(*) 1 punkt ECTS, odpowiada około 30 godzinom aktywności studenta
PoleKODZnaczenie kodu
Zamierzone efekty uczenia sięMSE_1A_C18b_W01Student describes issues concerning advanced manufacturing processes
Odniesienie do efektów kształcenia dla kierunku studiówMSE_1A_W07knows and understands the principles of functioning and operations of systems, apparatus and technological equipment with instrumentation, especially in the context of manufacturing and processing of materials
Cel przedmiotuC-1to get knowledge about selected advanced manufacturing technologies
Treści programoweT-W-1Principles of the kinetic theory of gasses
T-W-2Magnetron sputtering in coatings and thin films deposition
T-W-3Lithography and surface etching
T-W-4Vapor deposition techniques for growing nanostructures: chemical vapor deposition (CVD) and physical vapor deposition (PVP) and their modification
T-W-5Thin polymer films formation by LBL and sping coating techniques; thin biological layers formation
T-W-6High energetic beams used for thin films deposition and their influence on coating structure and properties; process parameters selections; kinetics of coatings growth
T-W-7Rapid protopyping of polymers using photocuring and thermoforming prosessing (FDM, SLA)
T-W-8Electrospinning of polymer nanofibres
Metody nauczaniaM-1interactive lectures, use of presentation (e.g. Powerpoint), films
Sposób ocenyS-1Ocena podsumowująca: written exam
Kryteria ocenyOcenaKryterium oceny
2,0
3,0Student describes selected issues at a basic level (score => 50%)
3,5
4,0
4,5
5,0
PoleKODZnaczenie kodu
Zamierzone efekty uczenia sięMSE_1A_C18b_U01Student has skills in advanced manufacturing processes
Odniesienie do efektów kształcenia dla kierunku studiówMSE_1A_U08being able to plan and execute processes of manufacturing of selected materials
Cel przedmiotuC-2formation of skills in the area of technological processes preparation and carrying out.
Treści programoweT-A-1Study on influence of synthesis parameters on the physicochemical properties of selected nanostructures produced via vapor deposition techniques: case studies (10h)
T-L-1Influence of process parameters on coating deposition by magnetron sputtering techniques
T-A-2Kinetic theory of gases – solving problems
T-A-3Proper design of adhesive joints. Case analysis and theoretical prediction of joint’s bearing capacities
T-L-2Advanced deposition of polymer thin films by MAPLE method
T-L-3Influence of process parameters on thin film deposition by pulsed laser and pulsed electron beam method
T-L-4Formation of FexN layers under variable nitriding potential during gaseous nitridation of iron
T-L-5Magnetron sputtering for preparation of sandwich structure nanolayers
T-L-6Attenuation effect of thin films in EDS/XPS spectroscopies
T-L-7Modification of particle size obtained via magnetron sputtering via sintering
T-L-8Experimental comparison of adhesive joints strength prepared wit different polymer adhesives (part I – preparation, part II -determination of strength)
T-L-9Degradation of waste polymer into metal-organic framworks (MOFs)
T-L-10SLA manufacturing technology. Design, printing and post-processing
Metody nauczaniaM-2Auditorium Exercises
Sposób ocenyS-2Ocena formująca: questions
S-3Ocena formująca: reports
Kryteria ocenyOcenaKryterium oceny
2,0
3,0Student describes selected issues at a basic level (score => 50%)
3,5
4,0
4,5
5,0
PoleKODZnaczenie kodu
Zamierzone efekty uczenia sięMSE_1A_C18b_K01Competences in advanced manufacturing of engineering materials
Odniesienie do efektów kształcenia dla kierunku studiówMSE_1A_K02acknowledges the importance of knowledge in solving cognitive and practical problems and is able to consult with experts if it is difficult to solve the problem on its own
Cel przedmiotuC-1to get knowledge about selected advanced manufacturing technologies
Treści programoweT-W-1Principles of the kinetic theory of gasses
T-A-1Study on influence of synthesis parameters on the physicochemical properties of selected nanostructures produced via vapor deposition techniques: case studies (10h)
T-L-1Influence of process parameters on coating deposition by magnetron sputtering techniques
T-W-2Magnetron sputtering in coatings and thin films deposition
T-W-3Lithography and surface etching
T-W-4Vapor deposition techniques for growing nanostructures: chemical vapor deposition (CVD) and physical vapor deposition (PVP) and their modification
T-W-5Thin polymer films formation by LBL and sping coating techniques; thin biological layers formation
T-W-6High energetic beams used for thin films deposition and their influence on coating structure and properties; process parameters selections; kinetics of coatings growth
T-A-2Kinetic theory of gases – solving problems
T-A-3Proper design of adhesive joints. Case analysis and theoretical prediction of joint’s bearing capacities
T-L-2Advanced deposition of polymer thin films by MAPLE method
T-L-3Influence of process parameters on thin film deposition by pulsed laser and pulsed electron beam method
T-L-4Formation of FexN layers under variable nitriding potential during gaseous nitridation of iron
T-L-5Magnetron sputtering for preparation of sandwich structure nanolayers
T-L-6Attenuation effect of thin films in EDS/XPS spectroscopies
T-L-7Modification of particle size obtained via magnetron sputtering via sintering
T-L-8Experimental comparison of adhesive joints strength prepared wit different polymer adhesives (part I – preparation, part II -determination of strength)
T-L-9Degradation of waste polymer into metal-organic framworks (MOFs)
T-L-10SLA manufacturing technology. Design, printing and post-processing
T-W-7Rapid protopyping of polymers using photocuring and thermoforming prosessing (FDM, SLA)
T-W-8Electrospinning of polymer nanofibres
Metody nauczaniaM-1interactive lectures, use of presentation (e.g. Powerpoint), films
M-3Laboratory exercises
Sposób ocenyS-1Ocena podsumowująca: written exam
S-3Ocena formująca: reports
Kryteria ocenyOcenaKryterium oceny
2,0
3,0Student describes selected issues at a basic level (score => 50%)
3,5
4,0
4,5
5,0